Vehicles
40 not categorized PORSCHE 930 ROD BUSHINGSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.40030I These 4340 chromoly steel i-beam connecting rods are made to the tightest tolerences exclusively for your Porsche. Fully machined billet, (not forged), these are surface peened hardened, cryogenically treated, and balanced within a gram. They come complete with aerospace-quality arp 2000 fasteners and ampco 45™ bushings. When only the best will do, these rods are built to the extreme. General Fitment911 1978-83
$1,815.00
Make a selection 150TBR900 Replace worn-out original front control arm / wishbone bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is located at the front of the control arm / wishbone. The correct matching poly-graphite bushing for the front of the control arm is part # 150tbf900 sold individually. 2 necessary per car.
$49.50
Make a selection 150TBF900 Replace worn-out original front control arm / wishbone bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is located at the front of the control arm / wishbone. The correct matching poly-graphite bushing for the rear of the control arm is part # 150tbr900 sold individually. 2 necessary per car.
$48.40
Make a selection 904788 Forged from the highest quality steel, each torsion bar is ground to provide a constant spring rate, chemically coated to protect against rust and then matched in pair sets to ensure that both sides of the car are equally suspended. All performance products torsion bars are guaranteed for 3 years against breakage. Note: worn torsion bar bushings will shorten the life of torsion bars. Our 3-year guarantee will remain valid only when bushings are in good condition at time of installing new torsion bars. Sold in pairs. General Fitment914 1970-76
$370.99
Make a selection 911944 Forged from the highest quality steel, each torsion bar is ground to provide a constant spring rate, chemically coated to protect against rust and then matched in pair sets to ensure that both sides of the car are equally suspended. All performance products torsion bars are guaranteed for 3 years against breakage. Note: worn torsion bar bushings will shorten the life of torsion bars. Our 3-year guarantee will remain valid only when bushings are in good condition at time of installing new torsion bars. 23.5 mm effective rate. Sold in pairs. General Fitment914 1970-76
$370.99
Make a selection 91434701006 Quality new replacement steering rack manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. Includes: - steering joint bushings - bellows retainers - outer retaining spring - bellows - inner retaining spring - steering rack coupler disc - steering rack coupler disc lock plate sold individually. 1 necessary per car. View/Change Diagram
From $396.75
Make a selection 911FDLNK Upgrade your stock front swaybar with this simple bolt in replacement for the factory drop links.
$205.00
Make a selection 91442423902 This reproduction boot fits on the plastic cover of the shift console at the transmission and keeps dirt out of the bushings for extended life. It replaces the no longer available shift linkage boot for your side-shift 914 View/Change Diagram
From $21.00
Make a selection 96437504381 Replace your worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushing. This is manufactured of rubber with a 75-shore hardness value. 75-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings rubber has a shore hardness value of 75 (like rs models) made in Germany this mount is a high-quality OEM (original equipment manufacturer) replacement part, designed to perform like t...(choose a part on the right to read more)
From $199.99
Make a selection 98656188100PRM Rubber bushing attaches to other end of convertible top push rod (part# 986 561 279 01-prm)
$5.50
Make a selection FVD3310212291 Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. It offers rs style handling characteristics, superior durability and is still forgiving enough for street use. - better handling. - makes precision adjustments of the suspension easier. - does not produce road noise. - shore hardness value of 85. - direct OEM replacement. - more forgiving for street use. -includes press tools and grease for easier assembly. Sold as a set. 1 kit is necessary per car. Please note: this fits the 964 c2 / c4 and rs america. Not keen on installing or having the bushings installed at a shop? Please check out our part # FVD33399603b8 and FVD33399603b8, we wil...(choose a part on the right to read more)
$902.00
Make a selection 150PB1027 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's 911 models from 1978-89 if fitted with an 18mm original rear sway bar.
$49.50
Make a selection FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$764.50
Make a selection FVD34391101SET Replace worn-out original front lower control arm bushings to return your car to its intended suspension geometry and steering feedback. Features: better handling reduces that sloppy steering feel does not produce any noise like the teflon bushings. Rubber has the original shore hardness value of 65 (like oem) fit's like oem, simple installation made in Germany if you are looking for a sportier upgrade we suggest our sport lower control arm set, part # FVD34391192set. Set is sold per axle. 2 necessary per car.
$152.90
Make a selection FVD34791130 Enhance steering precision and steering feedback by simply replacing your original tie rods. Turbo tie rods use a spherical inner joint instead of soft rubber bushings. They offer quicker steering response, more sensitivity and more precision. These are standard length we highly recommend them for lowered vehicles with bump steer kits like part # FVD34791100 or FVD347911930 . We also offer turbo tie rods in longer lengths for other applications, check part # FVD34791180r and FVD34791181ry this kit is manufactured in Germany by an OEM supplier, made from high carbon steel and 7075 t6 aluminum. Kit includes: 2 qty. Outer tie rods 2 qty. Inner tie rods 2 qty. Spacing washers 2 qty. Boots 2 qty. Castle nuts 2 qty. ...(choose a part on the right to read more)
$222.24
Make a selection FVD37504332R Replace the worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushings. These are manufactured of rubber with an 85-shore hardness value. 85-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings. Rubber has a shore hardness value of 85 (like rs models) made in Germany sold as a set. 1 necessary per car.
$152.90
Make a selection FVD424040 Ok, we know you are a driving enthusiast if you are shopping for a short shifter for your manual transmission. Driving enthusiasts appreciate a more direct connection to the car, transmission and road surface. If you are trying to clean up those long shifts and side to side play on the factory shifter you are certainly on the right track with this upgrade. This numeric racing short shift kit uses precision ball bearings on all axis' which produce 40% shorter throws with an almost gated like action. Short gated like throws increase your driving experience by enhancing a more direct, mechanical connection to your car. Once installed you will find joy with every shift and this will easily become one of your favor...(choose a part on the right to read more) General Fitment911 GT3 2007-11911 TURBO/GT2 2007-09 911 2009-12 911 2005-08 911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1998-05 CAYMAN 2009-12 CAYMAN 2006-08 BOXSTER 2009-11 BOXSTER 2005-08 BOXSTER 1997-04
From $740.94
Make a selection M500012 Moton club sport damper system Porsche 964 89-93 General Fitment911 1989-94
$7,356.15
Make a selection M500033 The 3-way adjustable moton damper features 15 positions of high speed bump, 6 positions low speed bump and 15 positions of rebound adjustment. The low speed bump adjuster is located on top of the high speed bump adjuster and can be adjusted in dependably. The low speed bump adjuster is very effective in helping to control body roll while adding to turn in and is effective in controlling pitch and squat. The 3-way adjustable moton damper is using, like the double adjustable damper, a unique blow off valve system in the canister to totally control curb stones and bumpy track conditions. General Fitment911 1998-05
$13,431.15
Make a selection M500041 Moton club sport damper system Porsche 996 turbo 01-05 General Fitment911 TURBO/GT2 2001-05
$8,166.15
Make a selection M500052 Moton club sport damper system Porsche Boxster incl s 97+ General FitmentBOXSTER 1997-04
$7,761.15
Make a selection FVD375996 Replace your worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushings. These are manufactured of rubber with a 75-shore hardness value. 75-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings. Rubber has a shore hardness value of 75 (like rs models) made in Germany this set is composed of high-quality OEM (original equipment manufacturer) replacement parts, designed to p...(choose a part on the right to read more) General Fitment911 1998-05
From $383.90
Make a selection M500072 Moton club sport damper system Porsche 993 93-98 General Fitment911 1989-94
$7,356.15
Make a selection M500133 Moton club sport damper system Porsche 997 turbo 07+ General Fitment911 TURBO/GT2 2007-09
$7,168.50
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |